USE : It is use to find out clay % of raw sand.
Specifications : Motor - 1/20 Hp Single Phase, Cycles 50, Speed Regulator, Timer, Glass Jar, Syphon, Wash Bottle, Sieve - 53 Micron Dia. 100 mm.

Use : It is use to find out AFS [Fineness No.] of sand
Specifications : Motor - 1/8 Hp Single Phase, Cycles 50, Sieve Set as per ISS No 53, 75, 106, 150, 212, 300, 425, 600, 850, 1700 Micron. Dia. 200 mm, OR (Sieves As Per Requirement) Timer 0-15 Min.

Use : It is use to drying the sand sample.
Specifications : Infra Red Lamp, 275 Watts, Drying Chamber Drying Pan.

Use : To Prepare the standard specimen
Specification : Contains standard specimen Jaw

Use : It is use to determine melting point of Resin Coated Sand.
Specification : With Heating Unit, Sand Distributor Digital Temperature Indicator And Controller, Brush.

Use : It is use to determine Pill Off and Build Up property of shell sand.
Specification : Heater - 1000 Watts, 230v.A.C. Supply. With Thermostat, Heating Plate, Funnel, Two Trays

Use : It is use to determine surface hardness of Core Mould.
Specification : Harden Tip, to Measure Hardness of Cores 0 To 100 No.

Use : It is use to determine Transverse Strength of resin coated sand.
Specifications : Suitable For Transverse Strength. Capacity 100 Kg/Cm 2 . Motorized Loading unloading Mechanism, Load Cell, Digital Transverse Strength Indicator. Suitable for specimen size 1/4 X 1"X4"

Use : It is use to determine Tensile Strength of shell sand in hot condition.
Specification :
1) Teflon coated Two Hot Plates, Controlled By Digital Temperature Indicator And Controller (0-300 o c).
2) Loading and unloading mechanisms operated by manually and auto by electronic control.
3) Digital Pressure Indicator to read tensile strength up to 55 kg/cm 2 .
4) Load Cell.
5) Hard crome plated tensile Jaw set.
6) Waste sand collection tray.
7) Jaw Lifting tongue.
8) Sand Filler Cum Scrapper
9) Cleaning Brush.
10) Working on 230 volt, 50 cycle, 1.6 Kw AC Power Supply

A. FOR HOT TENSILE TESTER
Use : It is use to standardize the pressure indicator and temperature indicator of Hot Tensile Tester.
Specifications : 1) It Consist plate with wire rope and hanger & temp indictor cum controller Calibrator at two different point
2) It require set of weights 20kg, 10kg & 5kg - 2 Nos.

B. FOR MOULD AND CORE HARDNESS TESTER
Use : it is used to standardize the mould & core hardness tester
Specifications : consist of instrument Clamping spring & 5nos standard weights.

Use : It is use to find out active clay % of sand.
Specifications : Stirrer - Magnetic Type, Titration Stand, Burette -50 ml. , Methylene Blue Bottle.

Use : It is use to find out liquid limit of Bentonite.
Specifications : Includes Rubber Base, Sliding Carriage, Metallic Bowl, Gauge Block And Grooving Tool

Use : It is use to mixing mulling purpose of Green Sand
Specifications : Capacity - 5 Kg [Batch], Motor with Gear Box 1/2 HP Single Phase, Scraper, Roller - 2 Nos. two ploughs, water sprinkling system

Use : It is use to prepare standard specimen for further test.
Specifications : With Sliding Weight, Lifting And Ramming Cam, Specimen Tube, Pedestal Cup And Stripper.

Use : It is use to determine Compression Shear, Tensile strength Green sand and Nobake sand ,co 2 sand.
Specifications : Suitable For Compression Strength, Tensile Strength, Transverse Strength With The Help Of Attachment,
Capacity : For High Gauge 13 Kg/Cm2 On Compression Scale For Low Gauge 1600 Gms/Cm2 On Compression Scale With Compression Pads

Use : It is use to determine Compression, Shear, Tensile strength of Green sand and Nobake sand, co 2 sand.
Specifications : Suitable For Compression Strength, Tensile Strength, Transverse Strength With The Help Of Attachment, Capacity 15 Kg/Cm2 On Compression Scale With Motorized Loading Mechanism, Load Cell, Digital Strength Indicator And Compression Pads

Use : It is use to determine Compression strength of Green sand
Specifications : with spring balance (0-2500 gm/cm 2 ), tray

Use : It is use to determine surface hardness of Green Mould.
Specifications : Digital Dial Indicator To Measure Hardness of Mould 0 - 100 No.

Use : It is use to determine surface hardness of Core Mould.
Specifications : Harden Tip, to Measure Hardness of Cores 0 To 100 No.

Use : It is use to determine the mouldability index of green sand.
Specifications : Sieve Drum, Timer, Infra Red Lamp, Pan & 9.5mm Sieve

Use : To determine the Shatter Index of moulding sand.
Specifications : Pillar, Top Housing Bracket, Anvil, 12.5 mm Sieve, Lid, pan

Use : It is use to determine wet tensile strength of green sand.
Specifications : Suitable For Wet Tensile Strength of green sand. Capacity 60 gm/Cm 2 Motorized Loading unloading Mechanism, Load Cell, pneumatic cylinder hot plate for heat the specimen up to 300 o C Digital Strength Indicator. Timer, Working on 230 volt, 50 cycles, 750 watts Power Supply.

Use : It is use to prepare standard specimen for further test.
Specifications :With Sliding Weight, Lifting And Ramming Cam, Specimen Tube, Pedestal Cup And Stripper.

Use : It is use to determine Compression Shear, Tensile strength Green sand and Nobake sand ,co 2 sand.
Specifications : Suitable For Compression Strength, Tensile Strength, Transverse Strength With The Help Of Attachment, Capacity : For High Gauge 13 Kg/Cm2 On Compression Scale For Low Gauge 1600 Gms/Cm2 On Compression Scale With Compression Pads

Use : it is used to standardize the mould & core hardness tester
Specifications : consist of instrument Clamping spring & 5 nos standard weights.

Use : it is used to prepare the standard specimen for Tensile
Specifications : consist of instrument Clamping spring & 5nos standard wts.

Use : it is used to prepare the standard specimen for transverse
Specifications : consist of instrument Clamping spring & 5nos standard wts.

Use : It is use to prepare standard specimen for further test.
Specifications :With Sliding Weight, Lifting And Ramming Cam, Specimen Tube, Pedestal Cup And Stripper.

Use : It is use to standardize Moisture Tester
Specifications :It consist Cap with master Gauge It is manufacturer Std.

E. For Mould And Core Hardness Tester
Use : It is use to determine the mouldability index of green sand.
Specifications : Sieve Drum, Timer, Infra Red Lamp, Pan & 9.5mm Sieve

Use : It is use to standardize the Universal Strength Machine.
Specifications : 1) For Low Capacity : it consists of Force Measuring Device having capacity 0 to 4 kg/cm 2 .on compression scale. Without NABL Calibration certificate As above with NABL Calibration certificate
2) For High Capacity : it consist of Force Measuring Device having capacity 0 to 12 kg/cm 2 .on compression scale. Without NABL Calibration certificate As above with NABL Calibration certificate

D. For Permeability Meter
Use : It is used to standardized permeability tester
Specifications : consist of rubber boss with standard orifice

Use : It is use to standardize Sand Rammer
Specifications :It consist precisian specimen tube, Height Gauge 50mm. with NABL Accreditation Lab certificate

C. As above with NABL Calibration certificate
For Permeability Meter Use : It is used to standardized permeability tester
Specifications : consist of rubber boss with standard orifice

D. For Permeability Meter
Use : it is used to standardize the mould & core hardness tester
Specifications : consist of instrument Clamping spring & 5 nos standard weights.

Use : It is use to standardize the Universal Strength Machine.
Specifications :1) For Low Capacity : it consists of Force Measuring Device having capacity 0 to 4 kg/cm 2. on compression scale. Without NABL Calibration certificate As above with NABL Calibration certificate
2) For High Capacity : it consist of Force Measuring Device having capacity 0 to 12 kg/cm 2 .on compression scale. Without NABL Calibration certificate