USE : It is use to collect the representative sand sample.
 Specifications : It consist of long pipe having one end Hard Tip with handle

 USE : It is use to collect the representative sand sample with proper mixing.
 Specifications : It consist of long pipe having one end Hard Tip with handle

 

 
 
 USE : It is use to find out clay % of raw sand.
 Specifications : Motor - 1/20 Hp Single Phase, Cycles – 50, Speed Regulator, Timer,
 Glass Jar, Syphon,  Wash Bottle, Sieve - 53 Micron Dia. 100 mm.

 

 USE: It is use to find out AFS [Fineness No.] of sand
 Specifications: Motor - 1/8 Hp Single Phase, Cycles – 50, Sieve Set as per ISS No 53, 75,  106, 150, 212,    
 300, 425, 600, 850, 1700 Micron. Dia. 200 mm, OR (Sieves As Per Requirement) Timer  0-15 Min.

 

 USE: It is use to drying the sand sample.
 Specifications: Infra Red Lamp, 275 Watts, Drying Chamber Drying Pan.

 USE: It is use to determine moisture % in Raw sand and Green sand.
 Specifications: Capacity 10 % Moisture With Single Pan Balance, Absorbent Compound And Carrying Case

 USE : It is use to determine Tensile Strength of shell sand in hot condition.
 Specification :
 01) Teflon coated Two Hot Plates, Controlled By Digital Temperature Indicator And  Controller (0-300 o c).
 02) Loading and unloading mechanisms operated by manually and auto by electronic  control.
 03) Digital Pressure Indicator to read tensile strength up to 55 kg/cm 2 .
 04) Load Cell.
 05) Hard crome plated tensile Jaw set.
 06) Waste sand collection tray.
 07) Jaw Lifting tongue.
 08) Sand Filler Cum Scrapper
 09) Cleaning Brush.
 10) Working on 230 volt, 50 cycle, 1.6 Kw AC Power Supply

 
 Use : To Prepare the standard specimen
 Specification : Contains standard specimen Jaw

  USE : It is use to determine melting point of Resin Coated Sand.
 Specification : With Heating Unit, Sand Distributor Digital Temperature Indicator And  Controller, Brush.

 
  USE : It is use to determine Pill Off and Build Up property of shell sand.
 Specification : Heater -1000 Watts, 230v.A.C. Supply. With Thermostat, Heating Plate,  Funnel, Two Trays

 USE : It is use to determine pill of f and build up property of shell sand.
 Specification : Heater -1000 Watts, 230V A.C. Supply. With Digital Temp. Indicator Cum Controller,
                    Heating Plate, Funnel, Two Trays

•

 USE : It is use to determine gas evolution in the shell sand.
 Specification : Heater-1200 Watts, 230v.,A.C.Supply.With Furnace Of 1200 o c Cap., Digital Temp.  
                   Indicator-Controller, Combustion Tube, Boats, Pusher Measuring Tube.

•

 USE : It is use to determine surface hardness of Core Mould.
 Specification : Harden Tip, to Measure Hardness of Cores 0 To 100 No.

•

 USE : It is use to prepare shell sand in hot condition to check the resin properties under standard condition.
 Specification : Mixture – Cap. - 5Kg [Batch], Motor with Gear Box1/2 HP Single Phase, Scraper - 2 Nos.,  window to see the inside process Heating unit – 6 kw, Blower – ¼ hp single phase, 230 AC volts.

•

Use: it is used to prepare the standard specimen for transverse strength of resin coated sand.
Specifications : Split Core Box To Prepare Transverse Specimens of 1/4X 1” X4” size with help of Hot  Tensile Tester

Use: It is use to determine Transverse Strength of resin coated sand.
Specifications : Suitable For Transverse Strength. Capacity 100 Kg/Cm 2 . Motorized Loading unloading Mechanism, Load Cell, Digital Transverse Strength Indicator. Suitable for specimen size 1/4X 1” X4”

 Use: It is use to determine to measure the distortions behavior of chemically bonded sand when exposed
 to heat.

 FOR HOT TENSILE TESTER

 USE: It is use to standardize the pressure indicator and temperature indicator of Hot  Tensile Tester.
 Specifications :
 1) It Consist plate with wire rope and hanger & temp indictor cum controller Calibrator at  two different point
 2) It require set of weights 20kg, 10kg & 5kg - 2 Nos.

 FOR MOULD AND CORE HARDNESS TESTER

 
  Use it is used to standardize the mould & core hardness tester
 Specifications : consist of instrument Clamping spring & 5nos standard weights.